skeda nuova..gia' guasta????

[SoGo]

dal nostro caro cesarex ho preso la airstar 2;

http://www.cesarex.com/product_info.php?products_id=227
oggi dopo aver montato il tutto,per ultimo ho collegato il cavo antenna terrestre alla stessa,visto che non ha bisogno di aver installato nulla sulla macchina essendo una ss2 terrestre,ma pur cambiando diverse prese tv non ho segnale nella skeda...con reel non scanna e con femon tutto a 0 come segnali..mettendo i setting dei canali della dvb-t terratec che ho nell'altra vdrbox schermo nero.
qui di seguito posto il mio lspci e dmeg,non si sa mai io non abbia fatto caso a qualche errore!!!!

vdr:~# lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 745 Host (rev 01)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:02.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:0b.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
00:0c.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card (rev 02)
00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)
vdr:~#


vdr:~# dmesg
Linux version 2.6.18-4-486 (Debian 2.6.18.dfsg.1-12etch2) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Wed May 9 22:23:40 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f63a0
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126960 pages, LIFO batch:31
DMI 2.2 present.
ACPI: RSDP (v000 AWARD ) @ 0x000f7e40
ACPI: RSDT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff6e40
ACPI: DSDT (v001 AWARD AWRDACPI 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x5008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Detected 1659.790 MHz processor.
Built 1 zonelists. Total pages: 131056
Kernel command line: root=/dev/hda1 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511568k/524224k available (1502k kernel code, 12040k reserved, 601k data, 256k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3324.22 BogoMIPS (lpj=6648451)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: AMD Athlon(tm) XP 2000+ stepping 02
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 4926k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb730, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Uncovering SIS18 that hid as a SIS503 (compatible=0)
Enabling SiS 96x SMBus.
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e0000000-e1ffffff
PREFETCH window: d8000000-dfffffff
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1180181152.036:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 256k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (40 C)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:02.2[D] -> GSI 19 (level, low) -> IRQ 169
ohci_hcd 0000:00:02.2: OHCI Host Controller
ohci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.2: irq 169, io mem 0xe2012000
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt 0000:00:02.3[A] -> GSI 23 (level, low) -> IRQ 177
ohci_hcd 0000:00:02.3: OHCI Host Controller
ohci_hcd 0000:00:02.3: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.3: irq 177, io mem 0xe2010000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
8139cp 0000:00:0f.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:00:0f.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 19 (level, low) -> IRQ 169
eth0: RealTek RTL8139 at 0xe400, 00:0a:e6:18:fc:e5, IRQ 169
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS745 ATA 100 (2nd gen) controller
ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
usb 1-1: new full speed USB device using ohci_hcd and address 2
hda: SAMSUNG SV3012H, ATA DISK drive
usb 1-1: configuration #1 chosen from 1 choice
hdb: LITE-ON LTR-24102B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 58711968 sectors (30060 MB) w/1945KiB Cache, CHS=58246/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
hdb: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
sis630_smbus 0000:00:02.0: SIS630 comp. bus not detected, module not inserted.
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x5080
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected SiS 745 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 185
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
Linux video capture interface: v2.00
saa7146: register extension 'dvb'.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
intel8x0_measure_ac97_clock: measured 55404 usecs
intel8x0: clocking to 48000
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 18 (level, low) -> IRQ 185
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:0d:d5:b1
b2c2-flexcop: i2c master_xfer failed
ts: Compaq touchscreen protocol output
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: found the mt352 at i2c address: 0x0f
DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 193
saa7146: found saa7146 @ mem e0ba6000 (revision 1, irq 193) (0x13c2,0x000e).
DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.3).
adapter has MAC addr = 00:d0:5c:05:10:82
dvb-ttpci: info @ card 1: firm f0240009, rtsl b0250018, vid 71010068, app 80f12623
dvb-ttpci: firmware @ card 1 supports CI link layer interface
dvb-ttpci: Crystal audio DAC @ card 1 detected
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
DVB: registering frontend 1 (ST STV0299 DVB-S)...
input: DVB on-card IR receiver as /class/input/input3
dvb-ttpci: found av7110-0.
Adding 1253028k swap on /dev/hda5. Priority:-1 extents:1 across:1253028k
EXT3 FS on hda1, internal journal
loop: loaded (max 8 devices)
i2c_adapter i2c-1: SMBus Quick command not supported, can't probe for chips
it87: Found IT8705F chip at 0x290, revision 2
it87-isa 9191-0290: Detected broken BIOS defaults, disabling PWM interface
ndiswrapper version 1.44 loaded (smp=no)
usb 1-1: reset full speed USB device using ohci_hcd and address 2
ndiswrapper: driver sis163u (OEM,11/29/2004,5.1.1039.1020) loaded
wlan0: ethernet device 00:03:2f:3c:23:05 using NDIS driver: sis163u, version: 0x1000000, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0457:0163.F.conf
wlan0: encryption modes supported: WEP; TKIP with WPA; AES/CCMP with WPA
usbcore: registered new driver ndiswrapper
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [FUTS]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
wlan0: no IPv6 routers present
APIC error on CPU0: 00(02)
APIC error on CPU0: 02(02)
APIC error on CPU0: 02(02)
APIC error on CPU0: 02(02)
vdr:~#

grazie aspetto un vostro parere.

[antonio 7319]

ciao SoGo
io ho preso da cesarex una technotrend s-2300
http://www.cesarex.com/product_info.php ... ucts_id=99
ha funzionato per qualche giorno poi schermo mero solo audio
o provato con il tester sull'uscita video e a massa ho scritto per imail e fax acesarex ma non om risìcevuto nessuna risposta
(non saranno tutte difettose)
bay

[SoGo]

a me non risulta poco serio cesarex....compro sempre da lui....non mi rimane che provare su un pc windows....poi gli scrivo...

vediamo cosa dice!!!!!!

[alez]

@antonio 7319

Io avevo acquistato un prodotto difettoso da cesarex (ricevitore IR USB in bundle con la SS 2.6d) ma mi e' stato prontamente sostituito, la prima volta non mi aveva risposto alla seconda si, a quanto pare la prima mail era andata persa.

Per le sostituzioni, una volta verificato accuratamente che l'oggetto non funzioni, occorre spedirglielo allegando nel pacco il modulo RMA di assistenza che trovi sul suo sito:

.http://www.cesarex.com -> Servizio Clienti -> Resi e riparazioni -> Garanzia -> Scarica il modulo


ciao alez